xilinx USB Cable 找不到！

Pcbbar

驅動安裝結束，如下圖，下載器指示正常為綠燈，


$ n9 |! J6 E# |: }( M7 m8 [


- S6 L+ R( p4 o2 F/ @進入IMPACT界面時，點擊PROGRAM出現如下錯誤：
. {7 Q9 j1 F4 E/ K7 l/ j

6 g& q) }- _9 F3 rGUI --- Auto connect to cable...
2 c2 n/ ~- c  D# N; T; OINFO:iMPACT - Digilent Plugin: Plugin Version: 2.4.4
INFO:iMPACT - Digilent Plugin: no JTAG device was found.
# K3 s' J( E" t* I- ]! ~AutoDetecting cable. Please wait.
* m$ d% N1 G/ T0 _0 x*** WARNING ***: When port is set to auto detect mode, cable speed is set to default 6 MHz regardless of explicit arguments supplied for setting the baud rates
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Source driver files not found.
The Platform Cable USB is not detected. Please connect a cable.If a cable is connected, please disconnect
( I, `$ Z, r( j; z1 D: A7 Qand reconnect to the usb port, follow the instructions in the 'Found New Hardware Wizard', then retry
7 w4 A. T1 \  Z. ?4 T' p2 u3 }3 othe Cable Setup operation.
Cable connection failed.
Connecting to cable (Parallel Port - LPT1).
: R" ?/ t- {( f% `* p; D7 kChecking cable driver.
Your driver installation is not complete. Please re-run your application or run
2 _& B+ B9 s% K' N$ uinstall_drivers.exe from the ISE installation area as an Administrator to complete the driver installation.
/ V" T& ?2 a; i7 k+ ?3 tService using windrvr6.sys : SYSTEM\CurrentControlSet\Services\WinDriver6.
ImagePath = \SystemRoot\system32\drivers\windrvr6.sys.
Start = 3.
, ^2 e' A5 k1 u. d# O; Y& t  N& Q5 \ ErrorControl = 1.
Type=1.
, G+ E: ~5 \4 LCable connection failed.
" r6 |" p; |- G0 l; \Connecting to cable (Parallel Port - LPT2).
( s* p4 ]  c+ _' e" vChecking cable driver.
0 t7 R4 F: t2 L* \# YYour driver installation is not complete. Please re-run your application or run
install_drivers.exe from the ISE installation area as an Administrator to complete the driver installation.
Service using windrvr6.sys : SYSTEM\CurrentControlSet\Services\WinDriver6.
ImagePath = \SystemRoot\system32\drivers\windrvr6.sys.
Start = 3.
6 V. c' F( q8 T* a" j ErrorControl = 1.
Type=1.
Cable connection failed.
Connecting to cable (Parallel Port - LPT3).
Checking cable driver.
3 r. n3 q$ X+ R0 r! W* xYour driver installation is not complete. Please re-run your application or run
install_drivers.exe from the ISE installation area as an Administrator to complete the driver installation.
! H) r4 q" r+ t8 A) s* u& [Service using windrvr6.sys : SYSTEM\CurrentControlSet\Services\WinDriver6.
: r5 v% d+ w5 s+ T/ s ImagePath = \SystemRoot\system32\drivers\windrvr6.sys.
Start = 3.
: P6 }4 s$ ?. c* k8 v3 i  W ErrorControl = 1.
3 N. O! z3 r- e1 t8 q5 N. |3 t Type=1.
Cable connection failed.
Connecting to cable (Parallel Port - LPT4).
. j( m! O. G4 W9 \; s8 WChecking cable driver.
- F  O9 \0 ~' r# qYour driver installation is not complete. Please re-run your application or run
install_drivers.exe from the ISE installation area as an Administrator to complete the driver installation.
. s) E* {2 J9 y" T. x8 |Service using windrvr6.sys : SYSTEM\CurrentControlSet\Services\WinDriver6.
ImagePath = \SystemRoot\system32\drivers\windrvr6.sys.
3 o" M% h1 Z/ ]2 |$ f( j Start = 3.
* R+ D% Z9 x5 T5 V- d ErrorControl = 1.
Type=1.
Cable connection failed.
PROGRESS_END - End Operation.
Elapsed time =      2 sec.
" F) X1 J8 Z' `Cable autodetection failed.
WARNING:iMPACT:923 - Can not find cable, check cable setup !
# O0 X0 l# ~2 S" ]2 e

各位大神解圍，不勝感激！

PCB觀察

阿里電子

https://blog.csdn.net/qq_36775035/article/details/80714563

PCB觀察

經過了6天的摸索，終于成功了，祈禱，阿門！

Mira_PCB

樓主樓主，能問一下你是怎么解決的嗎

PCBQA

具體怎么解決，我跟你遇到的問題一模一樣，好些天都沒進展，麻煩你指導一下。

Pcbbar

重新安裝驅動

深度大腦

你好，我遇到了同樣的問題，也重新裝了ise自帶的驅動，仿真器的指示燈顯示正常（電路板不上電為橘黃色，上電是綠色），但是還是出現 你上述的問題。Can not find cable, check cable setup !
" j4 f; G* E4 B+ _3 C$ B可否聯系一下；e-mail：144605975@qq.com

電子工科男

我遇到的問題是打開cable set界面會閃退

larssix

77777777777777777777777